Pond Pro
Solar Can-Air SS Diffused Aeration System with Cabinet
- SKU:
- Solar-Can-AirSS
- Weight:
- 120.00 LBS
- Shipping:
- CAD.$350.00 (Fixed Shipping Cost)
Description
Solar Can-Air Pond Aeration for fish ponds, dugouts and lakes
All solar systems are shipped on a pallet via truck. You need to have the necessary equipment to unload the truck or to pick up your items at a depot. Depending on your location and access to equipment, extra delivery charges may apply.
- Durable Stainless Steel Base
- Self righting; just toss some hose in water and then the diffuser
- No gravel needed in the base to sink it - just lower into the water
- Easy to assemble and install
- No electricity in the water. This can be especially important where swimming is allowed.
- No floating equipment at the surface
- Reduce phosphates by 95%
- Low maintenance. Most maintenance and inspection may be conducted onshore
- Works in depths up to 35' deep
- Note: Will only operate in direct sunlight
- This system is sufficient to keep fish alive if sized correctly. Algae must be kept at a minimum to prevent oxygen depletion
- This system has an inverter built in to the system. This system is not meant for external inverters
- The solar components are not meant to be replaced. The solar drive is sensitive to power and can withstand a maximum of 400 voltage
* Fixed shipping is only valid to addresses on Mainland Canada*
**NOTE** For warranty to be valid, all systems sold with no cabinet must be:
A) out of the elements (snow, wind, dust)
B) be kept off the ground (on a shelf or post)
C) have a cooling fan blowing hot air AWAY from compressor out of the enclosure
Advantages Of Using A Can-Air Aeration System
- Made in Canada from family businesses.
- Energy-efficient Can-Air piston compressor with air inlet filter. Two year standard warranty three year warranty when purchased with cabinet.
- Pond Pro weighted tubing
- Can-Air diffuser assemblies with weighted base.
- All fittings and clamps necessary to assemble your system.
- Multiple diffuser systems include a manifold with valves to control air flow to each diffuser.
- 38% more diffuser area than most systems out there.
If there is no aeration currently in your fish pond, the diffuser should be lowered roughly half the depth, and then slowly lowered all the way to the bottom over the next few weeks at a rate of 2 feet every other week until it is at the pond bottom
If the diffuser is lowered to the bottom right away you risk stirring up toxic gases that could kill your fish. Lowering it slowly over time will eliminate this risk
Our aeration sizing recommendations to improve water quality and keep fish alive in cold & warm climates:
|
Area Covered by 1 Can-Air SS Diffuser |
|||
Northern Climates |
Southern Climates | |||
Pond Depth |
Good Ponds/Preventative |
Eutrophic/Problem Ponds |
Good Ponds/Preventative |
Eutrophic/Problem Ponds |
5-8 |
65’ x 65’ |
45’ x 45’ |
75' x 75' |
55' x 55' |
9-12 |
125’ x 125’ |
85’ x 85’ |
145' x 145' | 100' x 100' |
13-15 |
160’ x 160’ |
125’ x 125’ |
185' x185' | 145' x 145' |
16-20 |
210’ x 210’ |
160’ x 160’ |
235' x235 |
180' x 180' |
20+ |
290’ x 290’ |
220’ x 220’ |
325' x 325' |
245' x 245 |
30+ |
320' x 320' |
265' x 265' |
360' x 360' | 300' x 300' |
Can-Air Solar System Components
Can-Air 1 |
Can-Air 2 |
Can-Air 3 |
(1) Can-Air Cabinet with CA-55 Compressor & fan assembled (2) heat lines,brass fittings & valves (1) 100’ 3/8” sinking airline (1) Can-Air SS Diffuser Required Fittings (1) Solar Drive Required Wires (3) Solar Panels
|
(1) Can-Air Cabinet with CA-65 Compressor & fan assembled (2) heat lines, brass fittings and valves (2) 100’ 3/8” sinking airline (2) Can-Air SS Diffuser Required Fittings (1) Solar Drive Required Wires (3) Solar Panels
|
(1) Can-Air Cabinet with CA-125 Compressor and fan assembled (1) 3-way manifold (3) 100’ 3/8” sinking airline (3) Can-Air SS Diffusers Required Fittings (1) Solar Drive Required Wires (4) Solar Panels
|
Can-Air 4 |
Can-Air 5 |
Can-Air 6 |
(1) Can-Air Cabinet with CA-150 Compressor & fan assembled (4) heat lines, brass fittings and valves (4) 100’ 3/8” sinking airline (4) Can-Air SS Diffuser Required Fittings (2) Solar Drive Required Wires (4) Solar Panels
|
(1 ) Can-Air Cabinet with CA-65 and (1) Can-Air Cabinet with CA-125 Compressor & fan assembled (2) heat lines, brass fittings and valves (1) 3-way manifold (5) 100’ 3/8” sinking airline (5) Can-Air SS Diffuser Required Fittings (2) Solar Drive Required Wires (7) Solar Panels
|
(2) Can-Air Cabinet with CA-125 Compressor and fan assembled (2) 3-way manifold (6) 100’ 3/8” sinking airline (6) Can-Air SS Diffusers Required Fittings (2) Solar Drive Required Wires (8) Solar Panels
|